The following is an index of common definitions, terms and key phrases used associated with table saws.

In order to construct, fully grasp functions, adjust and also maintain any table saw, you must learn about these wood working words and phrases.

Anti-Kickback Pawls -- With sufficient installation and upkeep, this device may stop the workpiece from being back toward the front of the saw while ripping.

Arbor -- The metal shaft that affixes the blade, extending from the drive mechanism.

Bevel Cut -- A cutting procedure made using the blade with any angle besides 90° to the table top.

Blade Guard Assembly -- A metal or maybe plastic safety application that's secured over the saw blade. Its purpose would be to avoid the user from contacting the saw blade.

Compound Cut -- This is successfully done if a cross cut is produced making use of both a bevel angle and also a miter.

Cross Cut -- A procedure of cutting or shaping accomplished through the width or perhaps the grain of the material.

Cutterhead (planers and jointer planers) -- This is a spinning cutterhead that has adjustable knives or blades. The blades or knives take out material from the workpiece.

Dado Blade -- A single blade or set of blades utilized to cut rabbets as well as grooves.

Dado Cut -- A cutting operation utilizing a dado blade, cutting a flat based groove in the face of the material.

Featherboard -- Safety appliance employed to keep the workpiece against the rip fence as well as against the table top.

FPM or SPM -- It refers to the motion of the blade in feet per minute or strokes per minute.

Freehand -- A cutting process without employing a miter gauge, fence or some other aids to help the workpiece.

Gum -- A wood deposit that is gluey and sap-based.

Kerf -- The gap or ensuing cut within the workpiece during the cutting process.

Kickback -- An instance in which the workpiece is forced back to the user at high speeds.

Miter Cut -- Doing a cut with the workpiece at any direction towards the blade besides 90 degrees.

Non-Through Cut -- Performing a cut in which the blade does not cut through the depth of the material.

Parallel -- Having equivalent distance apart at every point alongside two given planes or lines.

Perpendicular -- Intersecting planes or lines creating right-angles. For instance, the blade is perpendicular to the table surface.

Pilot Hole (drill presses) -- A little hole drilled in a material that functions as a lead for drilling big holes efficiently.

Push Blocks -- Tool employed to hold the material during cutting procedures. This aid keeps away the hands of the operator from getting near to the blade.

Push Stick -- A safety device being used in pushing the material on a cutting operation. It is used more often during rip cutting thin materials. This aid keeps the hands of the owner away from the blade.

Rabbet -- Making an L-shaped route across the edge of the workpiece in a cutting procedure.

Revolutions Per Minute (RPM) -- The entire number of rotations made by an object in just a minute.

Rip Cut -- Using the rip fence to cut over the length of the workpiece in a cutting procedure.

Riving Knife -- Metal plate located behind the blade. It maintains the kerf opening within the wood when doing a cutting procedure.

Saw Blade Path -- The locations surrounding the blade. The area which will be cut or has been already cut by the blade.

Set -- The outward bend (or set) distance of the tip of the saw on the face of the table.

Snipe (planers) -- Depression made at either end of a workpiece by cutter blades if the material isn't appropriately supported.

Straightedge -- Device employed in checking parallelism, flatness, or maybe the regularity of the surface.

Thin Kerf Blade -- A blade with a kerf or thickness which is leaner compared to a normal blade.

Through Cut -- Cutting procedure where the blade cuts entirely over the thickness of the material.

Throw-Back -- If the material is dropped in to the blade or placed unexpectedly touching the blade, the tossing back of a workpiece is made.

Worktable -- Surface in which the workpiece rests while performing a cutting, drilling, planing, or sanding operation.

Please visit www.besttablesawreviewshq.com for a range of table saw reviews.